Tag Archives: kraken cam

Asus x99 Deluxe BIOS Ver. 1305

slight base Vcore increase

So many BIOS Versions have been released by ASUS for the x99 Delux series. What you might experience with 1203 and 1305 is a slight increase of “base voltage” on the Vcore.

When i keep using my old offset values (0.24 V) for the Vcore i do get 1.3 V on that i7-5930K. Pre 1204/1305 i did get 1.28 V.  Thats an increase of 0.2 V just by updating the BIOS.

 

CPU seems to respond better to what you throw at it

What i did also notice is that the CPU does respond, let’s say, more accurately to the frequencies and voltage you put through. It feels more straight.

In the past i could clock the CPU to 4.6 GHz @ 1.3 V and were able to boot and use Windows. That’s no longer possible. I would have to add quite a lot more voltage ontop of it to get it going at these settings.

What did the board achive so far with 1305?

Currently (02. feb. 2015) i am at

 

CPU freq. RAM freq. Uncore freq. CPU Vcore RAM Vcore Uncore
4350 Mhz 3070 MHz 3584 MHz 1.32 V 1.35 V 1.2 V

 

I just started to play with it and will slightly decrease the Vcore. I am still using offset values. Go Offset!

 

cpu-z_5930k_asus_x99_1305

 

Old sad story – prime95

After all the trouble and questions we had regarding prime95 and Hasswell-E. I decided to run prime95 tests with the Kraken x60 at “silent” and at “custom” mode.  I noticed that Core 0 is behaving quite unimpressed – because the Worker 0 in prime95 stopped stressing the Core for unknown reason. Kraken x60 is a ready-to-use watercooling solution for noobs and lazy people. However as you can see in the bottom box in Kraken Cam, the temperature peaked at almost 90 °C (86 °C) with “silent” configuration.

 

kraken_cam_kraken_x60_asus_x99_1305
BUT: this was NOT a prime95 HEAT test. Keep that in mind. Just ordinary stress test.

 

So i started the prime95 test again due to unknown abstinence of Core 0 and the temperature peaked at 78 – 81  °C.  Fans are NOT at 65%, Kraken CAM is fooling us here.

 

 

LED of your Kraken Heatsink lit up 24/7?

If you want your LED flavoured Kraken/Watercooling Heatsink to not glow when the system is powered off, change the ErP Setting in the BIOS to “S4 + S5”.

I still use Kraken x60 standard Fans. I do want to change those since weeks, or months but never completed this task yet. Maybe you can recommend some.

 

Kraken X60 Software – Kraken CAM vs Kraken Controls

Well, i’m using Kraken X60 water cooling system in my current 2011-v3 RIG with all that shiny stuff launched in september 2014, but initially i did use the “Kraken Controls” Software to configure and adjust my water cooling system.

 

Kraken X60 Software "Kraken Controls"
Kraken X60 Software “Kraken Controls”

 

When i installed the hardware and Kraken Controls these days, they had another software available to manage your cooling system. It’s called “CAM” or “Kraken CAM” and was at version 1.1.2, if i remember correctly.

 

Kraken LED when system powered off

If you want your LED flavoured Kraken/Watercooling Heatsink to not glow when the system is powered off, change the ErP Setting in the BIOS to “S4 + S5”.

 

Kraken CAM version 1.1.2 to 1.1.7

However the Kraken CAM version that was available didn’t work well with my new Intel i7-5930K and the Asus x99 Deluxe motherboard. The CPU temperature  couldn’t be read by the  software, like it can’t be read by Kraken Controls (see picture above: no CPU temperature) and the overall look and feel did remind me too much of Windows 8.x. So i sticked to Kraken Controls only and kept using it. Now, a month later, i gave it another try. The version of Kraken CAM is currently 1.1.7 and the CPU temperature is now being read by the software (picture below).

 

Kraken CAM Software
Kraken CAM Software 1.1.7

 

CPU temperature display not the only improvement?

The Kraken CAM software takes way more time to start than the Kraken Controls, which is a downside, but this will not be the point here. What i noticed first was, that it seeeeems to make my water cooling system run a lot smoother or lets say fluent :).  The fans do not spin up that much like they did before at almost equal temperatures results. Yes, there will be a difference in the fan curves between Controls and CAM, but the point are the temperatures. That can only mean, that the pump is being used more efficiently.

 

Chose Kraken CAM

No matter what they did here, i  write this post to just recommend you using the Kraken CAM software instead of Kraken Controls! I also doubt that they will put further development on the Kraken Controls software.

 

nokrakencontrols